High Load Aluminum Cable Tray 6061 T6 Alloy 2.0mm-2.5mm Thickness Low Maintenance
Product Details
High Load Aluminum Cable Tray
,Low Maintenance Aluminium Cable Tray
,6061 T6 Alloy Cable Tray
Some routes carry the backbone of a plant, and they cannot be taken out of service for repair. The BENDIN High Load Aluminium Cable Tray Low Maintenance uses a reinforced rail profile and heavy wall extrusion to carry dense power bundles with fewer supports and minimal deflection.
Low maintenance is built into the material. Aluminium does not rust, and the optional anodized or powder coated surface resists dust, moisture and mild chemicals, so the tray does not need repainting or replacement over a normal plant life. In tunnels and substations where access is difficult, that is a significant saving.
Load is distributed evenly through rungs and side rails to avoid local stress concentrations. Wide trays can be supplied with additional reinforcement, and hanger spacing is calculated so the system stays within its deflection limit under full load.
BENDIN confirms load capacity by calculation and physical testing and checks wall thickness and straightness on every lot. Customers receive traceable, consistent trays that behave as the design predicts.
Applications include substations, mining, heavy manufacturing and large infrastructure. Heavy duty brackets and trapeze hangers complete a support system that is designed to be installed once and then left alone.
| Certificate Held | Compliance Status |
|---|---|
| ISO 9001:2015 | Quality management system - certified |
| CE | CE conformity - declared |
| TUV | TUV tested - held |
| NEMA | NEMA VE 1 - compliant |
| Parameter | Specification |
|---|---|
| Working load | Up to 200 kg/m (span dependent) |
| Maximum span | Up to 6 m at rated load |
| Deflection limit | L / 200 |
| Side rail height | 75 / 100 / 150 mm |
| Width range | 200 - 1000 mm |
| Wall thickness | 2.0 / 2.5 / 3.0 mm |
| Alloy | 6061-T6 high strength aluminium |
| Maintenance | Rust free, wipe clean, no repainting |
BENDIN specializes in reinforced aluminium tray for high load routes and verifies performance in house. With OEM and ODM support and stable supply, we help infrastructure clients specify tray that will not need attention for years.
Up to 200 kg/m depending on span, staying within an L/200 deflection limit under rated load.
No. Aluminium will not rust, and the coated finish only needs occasional wiping.
Substations, tunnels, mining and heavy manufacturing plants with dense power bundles.
-
Flexible Wire Mesh Basket Cable Tray 50mm-600mm Width On Site Configuration
BENDIN high-strength wire cable trays offer heavy-duty steel construction with on-site cut-and-bend flexibility for custom layouts. Certified to IEC/EN 61537, NEMA VE1/VE2, CE, RoHS, and regional standards. Available in galvanized or 304/316L stainless steel, 50-600mm widths, with full accessories and test reports. -
Long Life Galvanized Cable Trunking 85um Zinc Heavy Duty Rust Resistant 2m-3m Length
BENDIN heavy-duty galvanized steel cable trays: Q235 steel with 65-85um zinc coating for 25+ years maintenance-free life. Carry up to 180 kg/m over 6 m spans. ISO 9001 & CE certified, widths 150-900 mm, custom lengths available. -
Weatherproof Galvanized Cable Trunking 900mm Width High Strength 2m-3m Section
BENDIN weatherproof galvanized cable trays use high-strength steel and hot dip galvanized finish for outdoor durability against rain, UV and temperature cycling. ISO 9001 and CE certified, with widths 100-900 mm, engineered wind load spans, and custom support spacing options. -
600mm Width Galvanized Steel Cable Tray Outdoor UV Frost Resistant 2m-3m Length
BENDIN outdoor hot dip galvanized cable trays resist UV, rain and temperature swings from -40 to +150°C. Perforated trough bases drain water and ventilate cables. Post-fabrication galvanizing protects cut ends; ISO 9001 and CE certified, with custom coating or stainless steel options for coastal sites.
