Ventilated Aluminum Wire Tray 1.2mm-2.0mm Sheet Transformer Room Heat Dissipation
Product Details
Ventilated Aluminium Cable Tray
,6063 T5 Ventilated Aluminium Tray
,Ventilated Aluminium Trunking
Heat is the quiet killer of cable life, and the BENDIN Durable Aluminium Cable Tray Ventilated is designed to let it escape. A large open area slot pattern creates natural convection, allowing warm air to rise away from the conductors so cables run cooler and last longer.
Durability comes from the section itself. Thick wall aluminium rails and rungs resist vibration, impact and long term fatigue, so the tray keeps supporting cables even in busy industrial plants where steel alternatives would corrode or deform.
The slots are deburred and rounded. That detail protects cable jackets during pulling and means the ventilation benefit is not paid for with insulation damage. It also makes inspection easier, because cables stay visible along the whole route.
BENDIN controls slot pitch and rail geometry with automated punching and in house extrusion, keeping airflow consistent from section to section. Anodized or powder coated finishes extend the service life in humid and dusty conditions.
This tray is right for transformer rooms, generator halls, solar plants and factory distribution where heat build up matters. Where partial protection is needed, perforated covers can be added without eliminating ventilation.
| Certificate Held | Compliance Status |
|---|---|
| IEC 61537 | Cable tray systems - compliant |
| BS EN 61537 | European cable tray systems - compliant |
| NEMA/CSA | NEMA VE 1 / CSA - compliant |
| Parameter | Specification |
|---|---|
| Open area | Up to 40 percent ventilation |
| Slot size | 10 x 50 mm typical |
| Slot pitch | 25 mm centres |
| Cable fill ratio | Up to 40 percent of cross section |
| Alloy | 6063-T5 / 6061-T6 aluminium |
| Wall thickness | 1.2 / 1.5 / 2.0 mm |
| Width range | 100 - 800 mm |
| Finish | Mill / anodized / powder coated |
BENDIN manufactures ventilated tray with tightly controlled slot patterns and durable alloy selection. We advise on open area, cable fill and airflow so the finished system meets both thermal and mechanical targets.
-
Flexible Wire Mesh Basket Cable Tray 50mm-600mm Width On Site Configuration
BENDIN high-strength wire cable trays offer heavy-duty steel construction with on-site cut-and-bend flexibility for custom layouts. Certified to IEC/EN 61537, NEMA VE1/VE2, CE, RoHS, and regional standards. Available in galvanized or 304/316L stainless steel, 50-600mm widths, with full accessories and test reports. -
Long Life Galvanized Cable Trunking 85um Zinc Heavy Duty Rust Resistant 2m-3m Length
BENDIN heavy-duty galvanized steel cable trays: Q235 steel with 65-85um zinc coating for 25+ years maintenance-free life. Carry up to 180 kg/m over 6 m spans. ISO 9001 & CE certified, widths 150-900 mm, custom lengths available. -
Weatherproof Galvanized Cable Trunking 900mm Width High Strength 2m-3m Section
BENDIN weatherproof galvanized cable trays use high-strength steel and hot dip galvanized finish for outdoor durability against rain, UV and temperature cycling. ISO 9001 and CE certified, with widths 100-900 mm, engineered wind load spans, and custom support spacing options. -
600mm Width Galvanized Steel Cable Tray Outdoor UV Frost Resistant 2m-3m Length
BENDIN outdoor hot dip galvanized cable trays resist UV, rain and temperature swings from -40 to +150°C. Perforated trough bases drain water and ventilate cables. Post-fabrication galvanizing protects cut ends; ISO 9001 and CE certified, with custom coating or stainless steel options for coastal sites.
