Lightweight Aluminum Cable Tray 6061 T6 Alloy 1.2mm 1.5mm 2.0mm High Strength
Product Details
6061 T6 Aluminium Cable Tray
,High Strength Aluminium Cable Tray
,Lightweight Aluminum Cable Tray
Strength to weight is the whole point of this product. The BENDIN Lightweight Aluminium Cable Tray High Strength uses a 6061-T6 alloy and a deeper, thinner walled rail to reach tensile strength above 205 MPa while staying near 1.4 kg per meter, so long routes can be carried on lighter, cheaper support steel.
The optimized section resists bending and torsion, which lets the tray span further between brackets before visible sag appears. For warehouses, retail halls and plant rooms where every extra hanger is a cost, that longer span translates directly into savings.
A high strength tray should still be practical to install. Two people can carry and locate a full section by hand, and the consistent punching means couplers line up without forcing. Cables sit on a smooth, well ventilated bed that keeps pulling friction low.
BENDIN verifies tensile and yield properties through in house mechanical testing and checks wall thickness on each extrusion. Predictable mechanical behaviour under load is what separates a genuine high strength tray from a simply thin one.
This tray suits long span cable routes, equipment frames and structures with tight load limits. Covers, bends and brackets are available in the same profile so the structural benefit is preserved along the entire run.
| Certificate Held | Compliance Status |
|---|---|
| ISO 9001:2015 | Quality management system - certified |
| Parameter | Specification |
|---|---|
| Alloy / temper | 6061-T6 aluminium |
| Tensile strength | Not less than 205 MPa |
| Yield strength | Not less than 180 MPa |
| Elongation | Not less than 10 percent |
| Weight | Approx. 1.4 kg/m at 200 mm width |
| Maximum span | Up to 6 m (load dependent) |
| Deflection limit | L / 200 under rated load |
| Wall thickness | 1.2 / 1.5 / 2.0 mm |
BENDIN engineers its own high strength aluminium sections and validates them in house. We help customers choose the lightest profile that still meets the load case, and we support OEM profiles and finishes for equipment builders.
-
Flexible Wire Mesh Basket Cable Tray 50mm-600mm Width On Site Configuration
BENDIN high-strength wire cable trays offer heavy-duty steel construction with on-site cut-and-bend flexibility for custom layouts. Certified to IEC/EN 61537, NEMA VE1/VE2, CE, RoHS, and regional standards. Available in galvanized or 304/316L stainless steel, 50-600mm widths, with full accessories and test reports. -
Long Life Galvanized Cable Trunking 85um Zinc Heavy Duty Rust Resistant 2m-3m Length
BENDIN heavy-duty galvanized steel cable trays: Q235 steel with 65-85um zinc coating for 25+ years maintenance-free life. Carry up to 180 kg/m over 6 m spans. ISO 9001 & CE certified, widths 150-900 mm, custom lengths available. -
Weatherproof Galvanized Cable Trunking 900mm Width High Strength 2m-3m Section
BENDIN weatherproof galvanized cable trays use high-strength steel and hot dip galvanized finish for outdoor durability against rain, UV and temperature cycling. ISO 9001 and CE certified, with widths 100-900 mm, engineered wind load spans, and custom support spacing options. -
600mm Width Galvanized Steel Cable Tray Outdoor UV Frost Resistant 2m-3m Length
BENDIN outdoor hot dip galvanized cable trays resist UV, rain and temperature swings from -40 to +150°C. Perforated trough bases drain water and ventilate cables. Post-fabrication galvanizing protects cut ends; ISO 9001 and CE certified, with custom coating or stainless steel options for coastal sites.
