Coastal Grade Aluminum Alloy Cable Tray Anodized Finish Salt Air Corrosion Resistant
Product Details
Corrosion Resistant Aluminum Alloy Cable Tray
,Anodized Aluminium Cable Tray
,Powder Coated Aluminium Trunking
Salt air, process chemicals and washdowns attack cable routes from the day they are installed. The BENDIN Corrosion Resistant Aluminium Cable Tray Heavy Duty answers that with a naturally oxide forming aluminium body plus an anodized or powder coated barrier that keeps chlorides and moisture away from the metal.
It is engineered for load as well as longevity. Thick side rails carry heavy power cables through plants where steel tray would be rusting within a season, and the coating is applied after forming so cut edges and punched holes are covered too, closing the weak points that normally start corrosion.
Each production lot is salt spray tested and the film thickness recorded, so buyers receive material with a predictable service life rather than a cosmetic finish. Splice plates and fasteners are supplied in matching protected grades to avoid galvanic attack at the joints.
Because BENDIN runs its own anodizing and coating lines, the alloy, extrusion and surface treatment are all under one quality system. That is why the tray keeps both its strength and its appearance in environments that destroy ordinary cable management.
Typical installations include chemical and fertilizer plants, desalination and wastewater works, port terminals and offshore modules. Standard bends, tees and reducers are available in the same finish so the whole route stays consistent.
| Certificate Held | Compliance Status |
|---|---|
| ISO 9001:2015 | Quality management system - certified |
| CE | CE conformity, EN 61537 cable tray systems - declared |
| Parameter | Specification |
|---|---|
| Alloy | 6063-T5 / 6061-T6 aluminium |
| Coating system | Anodized or polyester powder coat |
| Coating thickness | Anodized 15 - 20 um / powder 80 - 120 um |
| Salt spray life | Up to 1000 h (coated) |
| Working load | Up to 150 kg/m at 1.5 m span |
| Wall thickness | 1.5 / 2.0 / 2.5 mm |
| Service pH range | 3 - 11 (coated) |
| Service temperature | -40 to +80 degrees C |
BENDIN pairs in house extrusion with dedicated surface treatment lines, giving one accountable partner for corrosion resistant tray. We provide batch test reports and OEM or ODM support for projects with strict environmental requirements.
-
Flexible Wire Mesh Basket Cable Tray 50mm-600mm Width On Site Configuration
BENDIN high-strength wire cable trays offer heavy-duty steel construction with on-site cut-and-bend flexibility for custom layouts. Certified to IEC/EN 61537, NEMA VE1/VE2, CE, RoHS, and regional standards. Available in galvanized or 304/316L stainless steel, 50-600mm widths, with full accessories and test reports. -
Long Life Galvanized Cable Trunking 85um Zinc Heavy Duty Rust Resistant 2m-3m Length
BENDIN heavy-duty galvanized steel cable trays: Q235 steel with 65-85um zinc coating for 25+ years maintenance-free life. Carry up to 180 kg/m over 6 m spans. ISO 9001 & CE certified, widths 150-900 mm, custom lengths available. -
Weatherproof Galvanized Cable Trunking 900mm Width High Strength 2m-3m Section
BENDIN weatherproof galvanized cable trays use high-strength steel and hot dip galvanized finish for outdoor durability against rain, UV and temperature cycling. ISO 9001 and CE certified, with widths 100-900 mm, engineered wind load spans, and custom support spacing options. -
600mm Width Galvanized Steel Cable Tray Outdoor UV Frost Resistant 2m-3m Length
BENDIN outdoor hot dip galvanized cable trays resist UV, rain and temperature swings from -40 to +150°C. Perforated trough bases drain water and ventilate cables. Post-fabrication galvanizing protects cut ends; ISO 9001 and CE certified, with custom coating or stainless steel options for coastal sites.
