Electrical Cable Ladder Tray 150mm Width Pre Galvanized 3m-6m Section Build
Product Details
150mm Electrical Cable Ladder
,Galvanized Electrical Cable Ladder
,Compact 150mm Ladder Tray
Electrical Cable Ladder 150mm is the compact route for the many cable runs that do not need a wide tray: lighting sub circuits, small power, control and instrumentation, where a narrow ladder follows a wall, a ceiling void or a plant room without wasting space or material.
The ladder is produced in 150 mm usable width with rail heights of 50 mm to 100 mm and rung pitch of 225 mm or 300 mm, in 3 m modules, from galvanized steel, aluminum or stainless depending on the environment. The light section can be cut and fitted by one electrician and fixed with small brackets that suit blockwork, steelwork or a suspended ceiling grid.
The open rung geometry is what makes a narrow ladder useful: cables can be laid in from above, tied at each rung and inspected from below without removing a cover, and a new circuit can be added later without disturbing the existing bundle. Ventilation is unrestricted, so derating is minimal compared with a closed trunking.
Finish options cover the full range of indoor and outdoor work: pre-galvanized for dry internal routes, hot dip galvanized for plant and external runs, powder coat for visible commercial areas, and stainless or aluminum for washdown and coastal sites. Every option keeps cut ends protected.
BENDIN manufactures this ladder at 10000 m per week with 180 staff and thirty years of cable support experience, exporting 60 to 70 percent of output to electrical contractors and distributors. Each batch is checked for width tolerance, rung spacing and coating, and short cut lengths can be supplied for retrofit work.
Minimum order 100 m, delivery on request, 5 to 20 USD per metre, pallet packing, terms T/T, D/A or D/P. Tell us the route length, the number of circuits and the environment and we will confirm material, finish and bracket spacing.
Certification and Standard Reference| Standard / Specification | Scope of Application | BENDIN Status |
|---|---|---|
| IEC 61537 | Load and deflection of the compact ladder | Design calculation and continuity check per order |
| ISO 1461 / EN 10346 | Galvanized coating options | Coating thickness measured per batch; record supplied |
| IEC 61537 clause 10 | Earthing continuity of the route | Design calculation and continuity check per order |
| ISO 9001:2015 | Quality management system | ISO 9001 certified; certificate copy on request |
| CE marking | EU construction products as applicable | CE Declaration of Conformity issued with shipment |
BENDIN holds ISO 9001 quality certification and issues CE Declarations of Conformity. The standards above state the design and test basis of this product; third party test reports or national approvals are supplied on request and are not implied unless confirmed in the contract.
Technical Parameters| Parameter | Standard Range | Customization Available |
|---|---|---|
| Usable width | 150 mm | 100 / 200 / 300 mm |
| Rail height | 50 / 75 / 100 mm | to drawing |
| Rung spacing | 225 / 300 mm | 450 mm |
| Material | Galvanized steel | aluminum, stainless |
| Module length | 3000 mm | cut to order |
| Finish | Pre-galvanized, HDG, powder coat | mill finish |
| Mass | 1.8 - 2.8 kg per metre | material dependent |
| Load class | Light duty per IEC 61537 | project specific |
Dimensions, rung spacing and surface treatment are produced to project drawings. Load and deflection calculations are issued for spans above 3 m.
Typical Applications- Lighting and small power sub circuits
- Control and instrumentation routes
- Retail, office and hotel back of house
- Plant rooms and service voids
- Laboratories and workshops
Q: Where is a 150 mm ladder the right choice?
A: On lighting sub circuits, control and instrumentation runs, and in ceiling voids or plant rooms where a wider tray would waste space and material.
Q: Which finish for an outdoor plant room?
A: Hot dip galvanized to ISO 1461 after fabrication, with stainless or aluminum where chlorides are present.
Q: Can circuits be added later?
A: Yes. The open rung format allows a new cable to be laid in and tied without dismantling the existing bundle.
Q: What is the minimum order?
A: Minimum order 100 m, prices from 5 to 20 USD per metre, pallet packing on T/T, D/A or D/P terms.
-
Flexible Wire Mesh Basket Cable Tray 50mm-600mm Width On Site Configuration
BENDIN high-strength wire cable trays offer heavy-duty steel construction with on-site cut-and-bend flexibility for custom layouts. Certified to IEC/EN 61537, NEMA VE1/VE2, CE, RoHS, and regional standards. Available in galvanized or 304/316L stainless steel, 50-600mm widths, with full accessories and test reports. -
Long Life Galvanized Cable Trunking 85um Zinc Heavy Duty Rust Resistant 2m-3m Length
BENDIN heavy-duty galvanized steel cable trays: Q235 steel with 65-85um zinc coating for 25+ years maintenance-free life. Carry up to 180 kg/m over 6 m spans. ISO 9001 & CE certified, widths 150-900 mm, custom lengths available. -
Weatherproof Galvanized Cable Trunking 900mm Width High Strength 2m-3m Section
BENDIN weatherproof galvanized cable trays use high-strength steel and hot dip galvanized finish for outdoor durability against rain, UV and temperature cycling. ISO 9001 and CE certified, with widths 100-900 mm, engineered wind load spans, and custom support spacing options. -
600mm Width Galvanized Steel Cable Tray Outdoor UV Frost Resistant 2m-3m Length
BENDIN outdoor hot dip galvanized cable trays resist UV, rain and temperature swings from -40 to +150°C. Perforated trough bases drain water and ventilate cables. Post-fabrication galvanizing protects cut ends; ISO 9001 and CE certified, with custom coating or stainless steel options for coastal sites.
