Overhead Rack Ladder Rack 6063 T5 200mm-700mm Width for Cable Suspension
Product Details
Lightweight Aluminum Cable Ladder
,Overhead Aluminum Cable Ladder
,Aluminum Overhead Ladder Rack
Aluminum Cable Ladder Lightweight Overhead Rack is the section specified when the structure above cannot take more dead load: suspended ceilings, mezzanine soffits, retrofitted halls and lightweight roof frames where a steel ladder would require additional steelwork or extra hanger points.
The rack is extruded from 6063 T5 aluminum in 200 mm to 700 mm usable widths with 100 mm or 150 mm rail height, rung pitch of 225 mm or 300 mm, and 2 m or 3 m modules that weigh around a third of an equivalent galvanized ladder. A two person crew can lift a full module into position without a hoist.
Light weight does not mean flexible: the extrusion profile carries a section modulus sized for the IEC 61537 deflection limit, and the rungs are fixed by pressing or riveting so the ladder behaves as a stiff beam between hangers. For heavier bundles a 6061 T6 alloy and a deeper rail are available.
Overhead installation benefits directly from the reduced mass. Hanger spacing can be optimised, anchors are smaller, and the ceiling grid sees less vibration and fewer fatigue cycles. Mill finish suits dry technical spaces, while anodizing or powder coating adds protection for humid or coastal halls.
BENDIN extrudes, finishes and fabricates this rack in house with 7000 m daily output, a 180 person production team and thirty years of cable route experience, exporting 60 to 70 percent to contractors and MEP specialists. Every batch is checked for straightness, rung position and wall thickness before it is packed on the pallet.
Minimum order 600 pcs, 25 working day delivery, 10 to 30 USD per piece, pallet packing, terms L/C, D/P or T/T. Send the ceiling grid and cable load and we will confirm alloy, rail height and hanger spacing for the route.
Certification and Standard Reference| Standard / Specification | Scope of Application | BENDIN Status |
|---|---|---|
| EN 755-2 / EN 573-3 | 6063 T5 and 6061 T6 extrusion properties | Material certificates and design reference supplied |
| IEC 61537 | Load, deflection and continuity of the rack | Design calculation and continuity check per order |
| ISO 9227 | Salt spray performance of anodized finish | Test report on request |
| ISO 9001:2015 | Quality management system | ISO 9001 certified; certificate copy on request |
| CE marking | EU construction products and LVD as applicable | CE Declaration of Conformity issued with shipment |
| RoHS 2011/65/EU | Restricted substances in surface treatment | Documentation on request |
BENDIN holds ISO 9001 quality certification and issues CE Declarations of Conformity. The standards above state the design and test basis of this product; third party test reports or national approvals are supplied on request and are not implied unless confirmed in the contract.
Technical Parameters| Parameter | Standard Range | Customization Available |
|---|---|---|
| Alloy and temper | 6063 T5 | 6061 T6 |
| Usable width | 200 - 700 mm | up to 1200 mm |
| Rail height | 100 / 150 mm | 75 - 200 mm |
| Rung spacing | 225 / 300 mm | 450 mm |
| Module length | 2000 / 3000 mm | up to 6000 mm |
| Mass | 3.2 - 4.8 kg per metre | height dependent |
| Surface | Mill finish | Anodized, powder coated |
| Load class | Per IEC 61537 | Project specific |
Dimensions, rung spacing and surface treatment are produced to project drawings. Load and deflection calculations are issued for spans above 3 m.
Typical Applications- Suspended ceilings and lightweight roof frames
- Data centre and telecom overhead routes
- Retrofit installations with limited anchor capacity
- Commercial and retail technical spaces
- Laboratories and clean rooms
Q: How much load can a suspended ceiling take?
A: That depends on the structure, not only the ladder. We provide the mass per metre and the hanger reactions so your engineer can confirm the anchor capacity.
Q: Is a 6061 alloy available for heavier loads?
A: Yes. 6061 T6 with a deeper rail is offered where the cable mass or span exceeds the 6063 table, with a deflection calculation issued for approval.
Q: Can it be cut and fitted on site?
A: Yes. Modules can be cut with a saw and the rung ends re finished, and the pressed rung joints stay tight without a weld.
Q: What is the minimum order?
A: Minimum order 600 pcs, delivery 25 working days, prices from 10 to 30 USD per piece.
-
Flexible Wire Mesh Basket Cable Tray 50mm-600mm Width On Site Configuration
BENDIN high-strength wire cable trays offer heavy-duty steel construction with on-site cut-and-bend flexibility for custom layouts. Certified to IEC/EN 61537, NEMA VE1/VE2, CE, RoHS, and regional standards. Available in galvanized or 304/316L stainless steel, 50-600mm widths, with full accessories and test reports. -
Long Life Galvanized Cable Trunking 85um Zinc Heavy Duty Rust Resistant 2m-3m Length
BENDIN heavy-duty galvanized steel cable trays: Q235 steel with 65-85um zinc coating for 25+ years maintenance-free life. Carry up to 180 kg/m over 6 m spans. ISO 9001 & CE certified, widths 150-900 mm, custom lengths available. -
Weatherproof Galvanized Cable Trunking 900mm Width High Strength 2m-3m Section
BENDIN weatherproof galvanized cable trays use high-strength steel and hot dip galvanized finish for outdoor durability against rain, UV and temperature cycling. ISO 9001 and CE certified, with widths 100-900 mm, engineered wind load spans, and custom support spacing options. -
600mm Width Galvanized Steel Cable Tray Outdoor UV Frost Resistant 2m-3m Length
BENDIN outdoor hot dip galvanized cable trays resist UV, rain and temperature swings from -40 to +150°C. Perforated trough bases drain water and ventilate cables. Post-fabrication galvanizing protects cut ends; ISO 9001 and CE certified, with custom coating or stainless steel options for coastal sites.
